-
Sale!Flanged 90° Elbow - Galvanized The flanged 90° Elbow - Galvanized bolts onto a steel flange, aluminum flange or plastic flange. We stock 6" and 8" Flanged 90° Elbow - Galvanized here at IrrigationSupplyParts.com, but have access to additional sizes. Please call us if you have questions or require a different size.
-
Sale!Flange Adapter (Flange x Ringlock Female) - Galvanized Bolts onto steel, aluminum or plastic flange, to transition from steel to Ringlock fittings or pipe. This flange adapter can also be used to insert a flanged valve into a system. Includes gasket. We also carry the Flange Adapter (Flange x Ringlock Male).
*The terms Ringlock and Circle Lock are used interchangeably on our website*
-
Sale!Thrust-Blocking PVC Pipe
- Water under pressure exerts thrust forces in piping systems at: changes in pipe size or direction, dead ends and valves.
- The design of thrust-blocking requires knowledge of the thrust generated and the bearing strength of the soil against which the thrust block will be placed.
- To be effective, a thrust block must:
- be placed against undisturbed or fully compacted earth.
- contact the fitting over a sufficiently large area so as not to create stress points on the fitting.
- have sufficient area on the soil to restrain the thrust without exceeding the bearing strength of the soil.
- Supply line 3" in diameter and larger shall receive concrete thrust blocks. Please research specifications for amount of concrete to be used for thrust block.
-
Sale!Thrust-Blocking PVC Pipe
- Water under pressure exerts thrust forces in piping systems at: changes in pipe size or direction, dead ends and valves.
- The design of thrust-blocking requires knowledge of the thrust generated and the bearing strength of the soil against which the thrust block will be placed.
- To be effective, a thrust block must:
- be placed against undisturbed or fully compacted earth.
- contact the fitting over a sufficiently large area so as not to create stress points on the fitting.
- have sufficient area on the soil to restrain the thrust without exceeding the bearing strength of the soil.
- Supply line 3" in diameter and larger shall receive concrete thrust blocks. Please research specifications for amount of concrete to be used for thrust block.
-
Sale!Series 3000 Air Vent and Vacuum Relief Valves protect both pressure and gravity systems against pipeline damage by releasing or venting entrapped air during system filling and preventing vacuum locks while the pipeline empties. This 2" Air Vent is normally installed by threading onto NPT (National Pipe Thread) steel or plastic risers. Features:
- Large orifice engineered to provide maximum air flow.
- Cast aluminum body combines lightweight strength and corrosion resistance.
- Synthetic rubber seal assures positive seal even with low head applications.
- Simple design ensures economical trouble-free performance.
- Maximum working pressure = 150 psi.
- Orifice diameter = 1.75"
- Height = 6.00"
- Width = 3.72"
For more information on Drip Irrigation, visit our Drip Irrigation FAQ (Frequently Asked Questions) page. -
Features:
- Working Pressure 600# PSI WOG
- PTFE reinforced seats and seals
- "K-Metal" non-corrosive stem
- Full Port, full flow capacity
- Forged Brass
-
This economical valve if made of durable, high quality PVC material which makes it last longer. No adjustment necessary. Brand Name: Matco Norca
-
This economical valve is made of durable, high quality PVC material which makes it last longer. No adjustment necessary. Brand Name: Matco Norca
-
This Threaded Brass Gate Valve consists of 200# (150 degrees F) non-shock, solid disc, non-rising stem and solder ends.
- ISO-9001
- 200 WOG - 125 SWP
- Full Port
- Cast Brass
- Non-rising Stem
- Threaded Bonnet
- Threaded Ends Conform to ANSI Standards B2.1
- Complies w/ NSF-61 for Low Lead
- Valves are Tested in Accordance w/ MSS-SP-82
- Sizes 3/4" -4“
-
Sale!This Riser Valve Stub Stem may need to be replaced occasionally on a riser valve. This stem is a 7 Pitch. **These are ordered by the size of the fitting on the riser and not the length of the bolt** Questions? Call us at 517-458-9741 or email us at info@triplekirrigation.com. We also stock the Riser Valve Stub Disc. Brand Name: Pierce
-
Sale!This is for a Riser Valve Stub Disc, this may need to be replaced occasionally on a riser valve. We also stock the Riser Valve Stub Stem.
-
This welds to the pipe to allow a valve opener to be attached to control water flow. Brand Name: Travis Pattern
-
Sale!This welds to the steel pipe to allow a valve opener to be attached to control water flow. We also stock the Riser Valve Stub Disc and the Riser Valve Stub Stem. Brand Name: Pierce
-
Sale!This threads on to the male pipe to allow a valve opener to be attached to control water flow. We also stock the Riser Valve Stub Disc and the Riser Valve Stub Stem. Brand Name: Pierce
-
Sale!This threads on to the female pipe to allow a valve opener to be attached to control water flow. We also stock the Riser Valve Stub Disc and the Riser Valve Stub Stem. Brand Name: Pierce
-
Sale!These nozzles ARE FOR the Komet Twin 101 Plus Taper Bore Nozzle these are the Old Style, they are Non-Threaded. You need to have a nozzle holder to hold these in place. The nozzle holders are sold separately. These nozzles ARE NOT for the Komet Twin 101 Ultra PC-24 Degree. Available in 11 sizes. Please see the chart below for more details.
Brand: Komet
-
Sale!These nozzles ARE FOR the Komet Twin 140 Plus Taper Bore Nozzle these are the Old Style, they are Non-Threaded. You need to have an nozzle holder to hold these in place. The nozzle holders are sold separately. These nozzles ARE NOT for the Komet Twin 140 Ultra PC-24 Degree. Available in 12 sizes. Please see the chart below for more details.
Brand: Komet
-
Sale!These nozzles ARE FOR the Komet Twin 160 Pro Taper Bore Nozzle these are the Old Style, they are Non-Threaded. You need to have a nozzle holder to hold these in place. The nozzle holders are sold separately. These nozzles ARE NOT for the Komet Twin 160 Ultra PC-24 Degree. Available in 14 sizes. Please see the chart below for more details.
Brand: Komet
-
Sale!These nozzles ARE FOR the Komet Twin 202 Pro Taper Bore Nozzle these are the Old Style, they are Non-Threaded. You need to have a nozzle holder to hold these in place. The nozzle holders are sold separately. These nozzles ARE NOT for the Komet Twin 202 Ultra PC-24 Degree. Available in 15 sizes. Please see the chart below for more details.
Brand: Komet
-
Sale!These nozzles ARE FOR the Komet Twin Max Taper Bore Nozzle these are Non-Threaded. You need to have a nozzle holder to hold these in place. The nozzle holders are sold separately. Available in 12 sizes. Please see the chart below for more details.
Brand: Komet
-
Sale!These nozzles are for the Komet Twin 101 Ultra PC-24 Degree these are the new style, they are threaded. These ARE NOT for the Komet Twin 101 Plus PC-24 Degree. Available in 9 sizes. Please see the chart below for more details.
Brand: Komet
-
Sale!These nozzles are for the Komet Twin 140 Ultra PC-24 Degree these are the new style, they are threaded. These ARE NOT for the Komet Twin 140 Plus PC-24 Degree. Available in 10 sizes. Please see the chart below for more details.
Brand: Komet
-
Sale!These nozzles are for the Komet Twin 160 ULTRA PC-24 Degree these are the new style, they are threaded. These ARE NOT for the Komet Twin 160 PRO PC-24 Degree. Available in 11 sizes. Please see the chart below for more details.
Brand: Komet
-
Sale!These nozzles are for the Komet Twin 202 ULTRA PC-24 Degree these are the new style, they are threaded. These ARE NOT for the Komet Twin 202 PRO PC-24 Degree. Available in 13 sizes. Please see the chart below for more details.
Brand: Komet
-
Sleeve Couplings are part of a full line of Die Cast Plugs, Bushings, Bell Reducers, Sleeve Couplers and Street Reducers manufactured by IACO (Irrigation Accessories Company). Precision machine threaded to NPT standards. Made of a Die Cast Zamac alloy that will not seize, rust or gall. Field tested and proven for over 50 years. Brand: IACO
-
Bushings are part of a full line of Die Cast Plugs, Bushings, Bell Reducers, Sleeve Couplers and Street Reducers manufactured by IACO (Irrigation Accessories Company). Precision machine threaded to NPT standards. Made of a Die Cast Zamac alloy that will not seize, rust or gall. Field tested and proven for over 50 years. Brand: IACO
-
Bell Reducers are part of a full line of Die Cast Plugs, Bushings, Bell Reducers, Sleeve Couplers and Street Reducers manufactured by IACO (Irrigation Accessories Company). Precision machine threaded to NPT standards. Made of a Die Cast Zamac alloy that will not seize, rust or gall. Field tested and proven for over 50 years. Brand: IACO
-
Pipe Plugs are part of a full line of Die Cast Plugs, Bushings, Bell Reducers, Sleeve Couplers and Street Reducers manufactured by IACO (Irrigation Accessories Company). Precision machine threaded to NPT standards. Made of a Die Cast Zamac alloy that will not seize, rust or gall. Field tested and proven for over 50 years. Brand: IACO
-
IACO has manufactured risers for over 50 years and they have stood the test of time! Risers manufactured by IACO are made of ¾” O.D. x .058 wall drawn type II aluminum 6063-T832, in lengths required by the purchaser. End fittings are made of swedge-fit die cast zinc alloy (Zamac #3: 40,000 psi tensile, 60,000 psi yield-compression), threaded to American Standard Pipe Thread (NPT) standards, with all threads clean and full.Brand: IACO
-
Capo Rubber Grommets with internal step combines with Xpando interference barb to hold 0ff-take firmly in place. This is an improved method of connecting low pressure irrigation tubes and drip lines to polyethylene tubes and PVC mainlines. 16 mm Size. Sold in packs of 25 grommets. For more information on Drip Irrigation, visit our Drip Irrigation FAQ (Frequently Asked Questions) page.
-
Xpando Take-Off Adapter is an improved method of connecting low pressure irrigation tubes and drip lines to polyethylene tubes and PVC mainlines. Easy to install, reducing both time and cost of installation. Innovative Xpando Take-Off Adapter with collapsible barb prevents pull-out and reduces grommet damage during the installation process. UV stabilized materials for long life. For agricultural, horticultural, vineyard and landscape applications. 16 mm size available. Sold in packs of 25 each. Please call for additional sizes. For more information on Drip Irrigation, visit our Drip Irrigation FAQ (Frequently Asked Questions) page.
-
Ratchet Clamps secure polyethylene tube to a wide range of fittings. Ratchet Clamps with smooth edge require no tools for installation. RATCHET CLAMP #18 fits 17 mm - 19 mm OD tube. Sold in packs of 100 each. Please call for additional sizes.
For more information on Drip Irrigation, visit our Drip Irrigation FAQ (Frequently Asked Questions) page.
-
Sale!Product Features • High-impact, heavy-duty plastic materials provide resistance to corrosion fertilizers and UV radiation. • Compact, sturdy, closed and protected ball engine. • Wide range of flow rates available in all three body angles (Low Angle-10 Degree, Low Angle-14 Degree or High Angle-25 Degree) • Three body angles allow for a wide range of wetted diameters. • Color-coded bayonet nozzle for easy operation and service. • Wetted diameters: 50 - 65 feet • Optional Flow Regulator. • Brown nozzle is used with Road Guard Only. Applications Orchards, Vineyards, Banana Plantations, Strawberries, Lettuce and Vegetables. Low-Angle for under-tree applications: Irrigation and Frost Protection (Please call us to special order Low Angle) High-Angle for over-crop applications: Irrigation, Cooling and Frost Protection Technical Data Flow rates 1.5 to 3.8 gpm Working pressure: 35 to 60 psi Wetted Diameters: 35 to 65 feet Click Jain's Rotating Sprinklers Brochure for more information. We stock two models at this time, but would be happy to special order any other models to meet your needs. Brand: Jain
-
Sale!Punch Tool For Layflat Tubing (Model # LFP-1) Hole Punch used for “punching” a hole in layflat tubing to insert 400 Series Barb Fittings. This punch is constructed of heavy duty plastic. It creates clean, precise holes for the layflat connectors. Brand Name: Jain
-
Sale!Hole Punch used for “punching” a hole in tubing to insert 400 Series Barb Fittings. This punch is constructed of heavy duty plastic. It creates clean, precise holes for the barb fittings. Brand Name: Jain
-
Sale!PC Emitter (CNL Feature) is an emitter with a separate barb for inlet and outlet installations. PC stands for Pressure Compensating while CNL stands for Closed No Leak. These emitters open at 5.5 PSI and close at 4.3 PSI. Sold in packs of 100 each. These Emitters (Pressure Compensating) deliver a consistent output of water, even with changes in pressure due to long runs of drip tubing or elevation changes, and come in .5 GPH (Blue), 1.0 GPH (Green), and 2.0 GPH (Red) sizes. This emitter may be inserted in 1/2" supply tubing by using a 1/4" punch tool or installed at the end of 1/4" distribution tubing or 1/4" dripper line due to its 1/4" barb (also known as a 250 barb) on one end. An emitter like this allows you to get water to exact locations unlike drip tubing which has built-in emitters spaced evenly in the tubing. For example, you could have a 1/2" distribution tubing running through your landscape bed. If a planting is near this tubing, you can insert an emitter near the planting. Another option is to install a 1/4" insert coupler in the 1/2" distribution tubing to connect a 1/4" dripper line to it. This line can then be run in and around plantings. At the end of the dripper line, install an emitter. This will allow you to irrigate the area. There are multiple options for installation using dripper line, distribution tubing and emitters. This is a pack of 100 emitters. Product Features
- CNL Feature Prevents Refill and Siphoning (Opens at 5.7 Psi, Closes at 4.3 Psi)
- Superior Clog Resistance
- Fully Pressure Compensating (10-65 Psi)
- Silicone Diaphragm Offers Precision and Long Life
- Large Turbulent Flow Path
- Made With UV Resistant Materials
- Color Coded for Ease of Identification
- Compact Size
- Low CV’s of 2.5% or Less
- Versatile Applications: Nursery, Greenhouse, Vineyard and Landscape
- Non-CNL Version Also Available (Please contact us for more details)
Click here to view Irritec's product brochure.
Brand Name: Irritec
-
Sale!Aqua Spray Sticks are engineered to provide an irrigation system that delivers both high performance and dependability. Ease-of-use, performance, and low-cost makes Aqua Spray Sticks an ideal product line for greenhouses, nurseries, and orchards. Simplicity in design and easy installation mean lower labor and material costs. Sold in packs of 100 each. We only stock green and gray spray sticks at this time. Please call us for additional options / special orders at (517)458-9741.
- Stake designed in a "H" pattern and taller for better stability in most soil medias
- Dual shut off capabilities: (A) Shut off tip on side instead of base of spray stick to eliminate contaminating tubing with soil (B) Second shut off capability on stake as an oval with use of our anti-kink nursery tubing
- Multiple flow rates and patterns - there's an Aqua Spray Stick that's right for your operation
- Made with UV-resistant resins, designed to last and reduce the possibility of tip damage
- Field friendly, may be assembled and disassembled in the field
- Fits all Dan parts and accessories
- Built-in shut-off tip
- Compatible with Leak Prevention Device (LPD)
- Designed to work effortlessly for years
- Simple design allows you to unclog Aqua Spray Sticks by simply pulling off the Spray Stick, cleaning the channel, and reinserting the same emitter back on the tubing
- Uses 187x125 polyethylene tubing
- Down spray and horizontal spray patterns available
Model # Color Volume Pattern Size Flow (20 PSI) In Stock ASBLK-6 Black High Flow Down 160 6" 15.0 Yes ASGRN-6 Green Medium Flow Down 160 6" 11.4 Yes ASAVCDO-6 Avocado Low Flow Down 160 6" 6.6 Special Order ASTERCTA-6 Terra Cotta Mini Flow Down 160 6" 4.2 Special Order ASBRN-6 Brown Low Flow Flat 90 6" 6.6 Special Order ASGRY-6 Gray Mini Flow Flat 90 6" 3.0 Special Order ASBLU-6 Blue Medium Flow Flat 360 6" 10.8 Special Order 
Brand Name: Jain -
Sale!Ejector Style Hole Punch used for “punching” a hole in rigid poly tubing to insert 1/4″ barb fittings. This punch is constructed of heavy duty plastic. It creates clean, precise holes for 1/4″ barb fittings. Ejector pin quickly cleans the punch tool of debris. Previous SKU: G-00177 Brand Name: Jain
-
Sale!VOE Stem Yoke (Clutch) 8" Item 10 in the illustration This clamps to the Valve Stub to allow water flow control in one direction. This fitting can be used with either Band & Latch OR Ringlock (except the 3″ size which is Band & Latch only).
-
Sale!VOE Stem Yoke (Clutch) 3" to 6" Item 10 in the illustration This clamps to the Valve Stub to allow water flow control in one direction. This fitting can be used with either Band & Latch OR Ringlock (except the 3″ size which is Band & Latch only).
